Staubli TX2-200 vs Yaskawa Motoman MH80 II: Robot Comparison

IN A NUTSHELL

Staubli TX2-200 vs Yaskawa Motoman MH80 II is a choice about heavy handling and tooling. Staubli TX2-200 and Yaskawa Motoman MH80 II differ in their working envelope, loading assumptions and engineering ecosystem. A useful decision starts with the exact mechanism and process, then checks whether either robot can execute the required path with the real tool attached. This comparison separates documented specifications from application-level engineering judgments.

Staubli TX2-200 vs Yaskawa Motoman MH80 II: quick verdict

Shortlist Staubli TX2-200 for 170 kg industrial handling within the documented 2209 mm working reference. Shortlist Yaskawa Motoman MH80 II for 80 kg industrial handling within the documented 2061 mm working reference. Neither is a universal winner: a robot that can carry the load may still fail the fixture-access, controller or maintenance requirements.

The numerical comparison below uses Staubli TX2-200 against Yaskawa Motoman MH80 II. The stated model scope matters when comparing later revisions or differently equipped installations. Published repeatability describes return to a taught position under specified conditions; it does not establish complete-cell accuracy or prove a faster production cycle.

Specifications and exact configuration scope

Read the reach row together with the geometric notes below. Manufacturers may specify an arm-link sum, a wrist-centre motion area or reach to the flange; those dimensions are not interchangeable. The table does not establish access to every point at every tool angle. Controller references identify reviewed packages, and actual compatibility must be confirmed by model, software version and region.

Staubli TX2-200: design and configuration

The Stäubli TX2-200 is a 6-axis industrial robot with a maximum payload of 170 kg, a reach of 2209 mm and a repeatability of ±0.02 mm. It is the heavy-payload arm of the TX2 range, used for palletizing, machine loading and unloading and the handling of large parts. The arm is floor mounted, is rated IP65 (IP67 with the pressurized arm) and runs on the Stäubli CS9 HP controller. Its maximum Cartesian speed is 12 m/s. Stäubli defines the TX2 envelope by exact arm length and revision. Its CS9 controller family supports a separate programming and safety ecosystem from Staubli. Standard, HE and other protected versions are distinct orders; no hygienic suitability is inferred for a standard arm. Verify the load diagram and the offered protection package at the intended tool orientation.

Yaskawa Motoman MH80 II: design and configuration

Yaskawa Motoman MH80 II is assessed as the named 6-axis configuration with 80 kg payload, 2061 mm reach and ±0.07 mm pose repeatability. This is the DX200-generation MH80 II, not the earlier DX100 MH80. The manufacturer’s own product listing pairs 80 kg payload with 2061 mm horizontal reach and ±0.07 mm repeatability. Its separately listed 3578 mm vertical coverage is not substituted into a radial reach comparison. Internally routed services can help limit interference, but their actual tooling load and replacement access still matter. Treat the supplied MH-generation controller, firmware, fieldbus interfaces and safety options as part of the offered configuration. A handling arm does not become a complete welding, cutting or dispensing cell merely because the mechanism can carry a process tool. Include the complete gripper or torch, adapters, part, dress pack and process forces in the load model; payload alone does not establish an allowable wrist offset or inertia. Simulate the full approach, loaded process and safe retreat, including fixture interference, stopping distance, cable clearance and the restart sequence after a protective stop. These are industrial platforms requiring appropriate safeguarding, rather than inherently safe human-contact systems. Repeatability is not calibrated absolute accuracy or evidence of demonstrated cycle time. Obtain confirmation of the actual generation, serial-number configuration, supplied condition, maintenance history, current spares and regional service. A legacy manufacturer specification supports technical identity without guaranteeing current production, local warehouse stock or the scope of a refurbished package.

For this pair, Yaskawa Motoman MH80 II offers 80 kg over the stated 2061 mm reference, compared with 170 kg and 2209 mm for Staubli TX2-200 example. Staubli TX2-200 has the larger stated distance by 148 mm, but this difference is only a preliminary layout indicator because reference points and joint envelopes can differ. Locate the actual fixture in each manufacturer model before treating this as usable extra working space.

Payload, tooling and a worked load example

Consider an illustrative total wrist load of 64 kg: a 16 kg tool and adapter package carrying a 48 kg part or product group. This arithmetic leaves 106 kg below the Staubli TX2-200 example’s nominal limit and 16 kg below Yaskawa Motoman MH80 II’s nominal limit. These are mass differences, not safety factors or a validated load approval. A heavy camera, valve block or retained material must be included before recalculating the total.

The example exposes the practical question: is the application limited by mass, by tool offset or by wrist rotation? Yaskawa Motoman MH80 II is the lower-or-equal nominal payload choice in this pair. Staubli TX2-200 offers more or equal headline mass capacity, but that alone cannot approve an eccentric fixture. Moving the same mass farther from the flange increases the moment, and spreading it increases rotational inertia. Manufacturer load diagrams and the actual centre of gravity govern the final allowable motion.

Model the empty, partly loaded and fully loaded tool states separately. A vacuum layer gripper, a weld torch with hoses or an inspection head may change its effective loading during the cycle. Set the controller’s load data for each supported state and validate the transition logic. A payload table cannot predict acceleration derating, cable pull or transient reactions at a machine interface.

Reach, orientation and fixture access

Build the same cell model for both candidates: base height, machine opening, fixture datum, maximum part size, tool extension and access for maintenance. Staubli TX2-200 provides a stated 2209 mm reference, while Yaskawa Motoman MH80 II provides 2061 mm. Check the deepest production pose and the return path with the loaded tool. An arm that just touches the target at full extension may have little freedom left to turn, retract or avoid a door.

For assembly and machine tending, test the gripper jaws in their open and closed positions. Include feeder replenishment, rejected-part disposal and tool changes. Check wrist flips and singularity avoidance along the whole path. A compact robot can fit a small fixture well, while a longer arm can simplify station placement; neither geometric benefit can be assumed without the actual model.

Precision and throughput: compare the same task

The comparison uses ±0.02 mm for Staubli TX2-200 and ±0.07 mm for Yaskawa Motoman MH80 II. These figures should be read in their documented configuration scope. Repeatability is not absolute accuracy, camera calibration accuracy or finished-part capability. Fixture variation, TCP calibration, thermal conditions and tool compliance can dominate the error at the process point, especially when the tool extends far from the flange.

Ask each integrator to execute the same representative path with the same payload model, tool length, process dwell and stop conditions. Report transfer time, settling time, process time and waiting time separately. Published standard cycles often use different loads and distances; dividing one catalogue cycle by another would not establish the production advantage of Staubli TX2-200 over Yaskawa Motoman MH80 II. Use a measured or validated application cycle before assigning a throughput benefit.

Programming, controls and production integration

Staubli TX2-200 is paired here with CS9 HP, while Yaskawa Motoman MH80 II uses DX200 reference; confirm the exact supplied MH-generation package. Controller names identify the review baseline rather than a guarantee that all interface options are included. Compare the actual software revision, teaching workflow, diagnostic tools, fieldbus licences and recovery procedures. An existing trained team and reusable production code may outweigh a small dimensional advantage. Obtain a demonstration of the same machine handshake and interrupted-cycle recovery on both platforms.

Specify the PLC handshakes before ordering: cycle request, ready, busy, complete, fault, part present and recovery authorization. Define how an interrupted operation resumes without repeating a dangerous or quality-critical action. Vision, force sensing, fieldbus communication and external-axis coordination must be checked as explicit included or optional functions. An Ethernet connector does not by itself prove that a particular industrial protocol or software interface is licensed and supported.

Configuration and communication detail

Protection, installation and maintenance

Match the precise protection package to the process. Standard, protected, cleanroom, foundry and washing configurations can have different seals, services and maintenance requirements. Do not transfer the best optional IP or cleanroom rating to an unprotected base model. Check the controller location, cable bend radius, available lifting access and base reactions with the installer.

Treat safe operation as a property of the complete task and installation. Include the tool, sharp workpiece edges, trapping points, dropped loads and machine access. These robot systems require task-specific safeguarding; payload or compact size does not establish safe unguarded operation. Plan tool replacement and fault recovery without dismantling the whole installation, and include connector access, lubrication and spare-cable replacement in the maintenance layout.

Price and lifecycle value

Arm prices: Staubli TX2-200 is listed from $120,000 and Yaskawa Motoman MH80 II is estimated from $48,000. Request configuration-specific quotations for Staubli TX2-200 and Yaskawa Motoman MH80 II. An arm-only number is not the price of a commissioned production cell. Ask for separate line items for controller, pendant, communication options, end effector, safety equipment, installation, acceptance, training and warranty. Price changes, regional support and included software can reverse an apparent hardware-cost advantage. Compare the same delivered scope before calculating payback.

Compare the installed production scope: tool, fixtures, sensing, guarding, machine interface, programming, acceptance and training. For heavy handling, include lifting, foundations, cable routing and fixture load verification. Keep purchase cost and recurring support costs separate. No payback figure is defensible until the actual cycle, yield, utilization and installation quotation are known.

Selection and acceptance plan

Advance Staubli TX2-200 when 170 kg industrial handling within the documented 2209 mm working reference solves the real constraint and its selected configuration passes the load and access checks. Advance Yaskawa Motoman MH80 II when 80 kg industrial handling within the documented 2061 mm working reference provides the more suitable process arrangement. Reject either candidate if a mandatory pose, protection requirement or controller function cannot be demonstrated. A purchasing shortlist should preserve these conditions instead of converting a single catalogue advantage into a blanket recommendation.

Before acceptance, agree the representative parts, tool states, operating sequence and quality criteria with both suppliers. Demonstrate cold start, normal production, rejected parts, interrupted cycles and controlled recovery. Record the final tool data and software backup. This turns the comparison into a repeatable purchasing decision and helps prevent a later fixture change from invalidating the original robot selection.

Motion architecture and functionality

Staubli TX2-200 has 6 arm axes and Yaskawa Motoman MH80 II has 6 arm axes. Both have six arm axes; equal axis counts do not establish equal joint travel, inner workspace or fixture access. Compare tool detection, sensing, machine I/O and recovery as separate delivered functions.

Industries and application fit

For Staubli TX2-200 vs Yaskawa Motoman MH80 II, use the actual part and process as the industry filter. Electronics, manufactured-component handling and machine tending are candidate uses when their tool mass, access and quality requirements fit the documented configurations. These are application-selection judgments, not claims that either exact model is installed at a named customer. A food, medical-device or clean-production application additionally requires the correct material, lubrication and protection package; the base model name does not establish hygienic or cleanroom compliance.

Frequently asked questions

Which robot is better for this application?

Staubli TX2-200 is the stronger starting point for 170 kg industrial handling within the documented 2209 mm working reference, while Yaskawa Motoman MH80 II is worth shortlisting for 80 kg industrial handling within the documented 2061 mm working reference. The final choice depends on the real loaded path, required protection, controls and acceptance results. Neither a higher payload nor a longer reach establishes a universal winner.

What payload should I use for the comparison?

Use 170 kg for the specified Staubli TX2-200 example and 80 kg for Yaskawa Motoman MH80 II, subject to all documented load and orientation conditions. Include the tool, adapters, sensors and carried part. Confirm exact configuration, controller, wrist loading and installation envelope.

Does the stated reach guarantee access to my fixture?

No. The comparison gives 2209 mm for Staubli TX2-200 and 2061 mm for Yaskawa Motoman MH80 II using the stated model references. Joint limits, reach reference points, wrist orientation, tool length and collisions determine whether the actual fixture is accessible. Simulate the full approach and exit path.

Can I use the best specifications from every family variant?

No. Keep each named model and revision intact. A different arm length, controller generation or protection option can change the relevant specification. Do not combine one version’s maximum payload with another version’s maximum reach.

Is repeatability the same as finished-part accuracy?

No. The stated values are ±0.02 mm for Staubli TX2-200 scope and ±0.07 mm for the competitor scope. Finished-part results also depend on fixtures, TCP calibration, sensing, thermal conditions and tool compliance. Validate the actual process instead of treating catalogue repeatability as a complete accuracy guarantee.

How should purchase prices be compared?

Use current written quotations for Staubli TX2-200 and Yaskawa Motoman MH80 II with the same arm, controller, software, tooling and commissioning scope. This comparison does not represent an ATC sales offer or stock confirmation. Historical review figures are not a substitute for a configuration-specific purchase quotation.

Can these robots operate safely next to people without guarding?

These specifications do not establish a safe unguarded installation. Assess the complete task, tool, load and machine interface, then implement and validate the required safeguarding and operating procedures. Do not infer collaborative operation from a compact arm, limited payload or education setting.

What should an acceptance test compare?

Use the same parts, actual tool load, fixture locations, path and quality criteria for Staubli TX2-200 and Yaskawa Motoman MH80 II. Check production timing, settling, interruptions and recovery. Include the most difficult loaded approach and retreat. Approve the exact delivered configuration and preserve its final settings.

Related ATC reviews

Read the Staubli TX2-200 review

Read the Yaskawa Motoman MH80 II review

Specifications describe the model scope identified above. Purchase pricing requires a current configuration-specific quotation. Confirm current manufacturer documentation, local supply, controller compatibility and the exact configuration before purchase.