Mitsubishi Electric RH-12FH vs Shibaura Machine THE400: Robot Comparison
Updated: 7 hours ago
IN A NUTSHELL
🔎 THE KEY DIFFERENCE Mitsubishi Electric RH-12FH5535-D has the higher stated load capacity and longer stated reach. Those figures help shortlist it for heavier loads or wider layouts, but do not prove a faster production cycle. |
→ CONSIDER Mitsubishi Electric RH-12FH5535-D Consider it when additional load capacity and reach matter. This article compares 12 kg and a 550 mm stated reach; include the gripper and part in the load. |
→ CONSIDER Shibaura Machine THE400 Consider it when its stated load and reach already cover your task and its controls fit your equipment. This article compares 5 kg and a 400 mm stated reach; include the gripper and part in the load. |
💡 THE TAKEAWAY For repetitive pick-and-place or assembly, check the actual vertical stroke and tool rotation as well as horizontal reach. Compare the same loaded cycle and installed quotation before deciding. |
Mitsubishi Electric RH-12FH vs Shibaura Machine THE400 is a choice about SCARA assembly and planar handling. Mitsubishi Electric RH-12FH5535-D and Shibaura Machine THE400 differ in their working envelope, loading assumptions and engineering ecosystem. A useful decision starts with the exact mechanism and process, then checks whether either robot can execute the required path with the real tool attached. This comparison separates documented specifications from application-level engineering judgments.
Mitsubishi Electric RH-12FH vs Shibaura Machine THE400: quick verdict
Shortlist Mitsubishi Electric RH-12FH for 12 kg planar handling within the selected 550 mm SCARA envelope. Shortlist Shibaura Machine THE400 for 5 kg planar handling within the selected 400 mm SCARA envelope. Both are four-axis SCARA candidates, so the decisive questions are planar access, vertical stroke, spindle inertia and the complete assembly cycle. Neither supplies independent tool pitch and roll.
The numerical comparison below uses Mitsubishi Electric RH-12FH5535-D against Shibaura Machine THE400. The stated model scope matters when comparing later revisions or differently equipped installations. Published repeatability describes return to a taught position under specified conditions; it does not establish complete-cell accuracy or prove a faster production cycle.
Specifications and exact configuration scope
Criterion | Mitsubishi Electric RH-12FH | Shibaura Machine THE400 |
|---|---|---|
Comparison configuration | Mitsubishi Electric RH-12FH5535-D | Shibaura Machine THE400 |
Payload used for comparison | 12 kg (maximum; rated benchmark load is separate) | 5 kg (maximum reference; subject to load chart) |
Reach / motion-area reference | 550 mm | 400 mm |
Axes | 4 | 4 |
Repeatability for this scope | ±0.012 mm (XY) | ±0.01 mm (XY) |
Controller reference | Matched CR750/CR751 F-generation package; exact selected arm specification | TSL3000 / matched TS5000 option |
Purchase-price basis | Configuration-specific quotation | Configuration-specific quotation |
Purchase pricing | Request a configuration-specific quote | Request a configuration-specific quote |
Read the reach row together with the geometric notes below. Manufacturers may specify an arm-link sum, a wrist-centre motion area or reach to the flange; those dimensions are not interchangeable. The table does not establish access to every point at every tool angle. Controller references identify reviewed packages, and actual compatibility must be confirmed by model, software version and region.
Mitsubishi Electric RH-12FH: design and configuration
Mitsubishi Electric RH-12FH is compared at 12 kg and 550 mm in the exact selected configuration. The mechanical reference is RH-12FH5535-D: four arm axes, 350 mm vertical stroke and ±0.012 mm XY repeatability. The selected configuration has 550 mm horizontal reach and a 350 mm Z stroke. The 700/850 mm arms and 450 mm stroke are different order specifications. The 550 mm model uses the documented ±0.012 mm XY value; longer-arm values must not be applied merely because the payload is also 12 kg. The catalogue distinguishes the 12 kg maximum wrist load from a 3 kg rated reference; maximum loading must not be used as the test load for a short standard-cycle claim. XY positional repeatability, Z repeatability and angular spindle repeatability are separate quantities with different units. A four-axis SCARA positions and rotates a level tool; it does not independently supply arbitrary wrist pitch and roll. Check spindle inertia, tool offset, vertical process forces, clearances at both ends of the Z travel and the actual loaded transfer. Match the CR750/CR751 F-generation arm/controller order code, software, safety options and delivered I/O rather than substituting a newer FR/CR800 package. Standard, oil-mist, waterproof and cleanroom builds are different specifications. Environmental options can change stroke, bellows clearance and installation requirements; cleanliness also depends on the manufacturer’s airflow/suction conditions. A published cycle benchmark does not establish a loaded production cycle, insertion accuracy or uptime. Include every tool, adapter, sensor, retained part and service line in the dynamic load model, then demonstrate the process and a safe recovery after a stop. Validate the floor-mounted support, base reactions and access around the entire arm sweep. Confirm the quoted generation, condition, spare-part support, regional service and actual price. Legacy documentation establishes technical identity without guaranteeing current local stock.
Shibaura Machine THE400: design and configuration
Shibaura Machine THE400 is compared using the THE400 reference with 5 kg maximum load, 400 mm horizontal SCARA arm length and ±0.01 mm (XY) repeatability. The manufacturer separately specifies a 1 kg rated load; the maximum mass is not a promise of the standard cycle time at full load. The selected controller baseline is TSL3000 / matched TS5000 option. 160 mm nominal Z travel; the TS5000-EMS package changes the stated stroke to 150 mm. Four SCARA axes provide planar positioning, vertical spindle motion and tool yaw; they do not provide arbitrary wrist pitch and roll. XY, Z and angular repeatability are different quantities. Include retained product, spindle tooling and services in the load, and validate eccentricity, inertia, insertion forces and cable travel. Standard cycle examples use a particular motion pattern and load; continuous operation must remain inside the effective load ratio. A 300 mm horizontal / 25 mm vertical test does not establish throughput for a different tray, settling time or insertion sequence. Controller choice, vertical stroke, environmental protection and ceiling mounting must match the exact order code.
For this pair, Shibaura Machine THE400 offers 5 kg over the stated 400 mm reference, compared with 12 kg and 550 mm for Mitsubishi Electric RH-12FH example. Mitsubishi Electric RH-12FH has the larger stated distance by 150 mm, but this difference is only a preliminary layout indicator because reference points and joint envelopes can differ. Locate the actual fixture in each manufacturer model before treating this as usable extra working space.
Payload, tooling and a worked load example
Consider an illustrative total wrist load of 4 kg: a 1 kg tool and adapter package carrying a 3 kg part or product group. This arithmetic leaves 8 kg below the Mitsubishi Electric RH-12FH example’s nominal limit and 1 kg below Shibaura Machine THE400’s nominal limit. These are mass differences, not safety factors or a validated load approval. A heavy camera, valve block or retained material must be included before recalculating the total.
The example exposes the practical question: is the application limited by mass, by tool offset or by wrist rotation? Shibaura Machine THE400 is the lower-or-equal nominal payload choice in this pair. Mitsubishi Electric RH-12FH offers more or equal headline mass capacity, but that alone cannot approve an eccentric fixture. Moving the same mass farther from the flange increases the moment, and spreading it increases rotational inertia. Manufacturer load diagrams and the actual centre of gravity govern the final allowable motion.
For the two SCARA configurations, model the tool inertia around the vertical spindle as well as total carried mass. A broad multi-part gripper can satisfy the mass limit while exceeding permitted rotational inertia. Set the controller load and inertia parameters for empty and loaded states, then check insertion stroke and any allowable vertical pressing force separately. Nominal cycle figures do not establish performance at maximum payload.
Reach, orientation and fixture access
Build the same cell model for both candidates: base height, machine opening, fixture datum, maximum part size, tool extension and access for maintenance. Mitsubishi Electric RH-12FH5535-D provides a stated 550 mm reference, while Shibaura Machine THE400 provides 400 mm. Check the deepest production pose and the return path with the loaded tool. An arm that just touches the target at full extension may have little freedom left to turn, retract or avoid a door.
For SCARA assembly, check the full XY sweep, inner dead zone and Z stroke. A horizontal reach figure does not establish that the spindle can descend into the fixture without the tool body or cable loop colliding. Vertical pressing force is a separate limit from payload. Validate screwdriving or insertion forces, spindle inertia and settling with the real fixture. Neither robot gains six-axis pitch and roll freedom merely by having enough horizontal reach.
SCARA motion and assembly fit
The selected Mitsubishi Electric RH-12FH5535-D and Shibaura Machine THE400 should be assessed on the same horizontal transfer, vertical insertion and rotation sequence. Smaller horizontal reach can support a compact bench; larger reach can serve more nests, but also changes the swept area and cable clearance. Check actual Z stroke and tool length against the lowest station and tallest obstruction. Compare XY repeatability with XY repeatability, while keeping Z and rotational values in their own units.
SCARA requirement | Mitsubishi Electric RH-12FH | Shibaura Machine THE400 |
|---|---|---|
Horizontal scope | 550 mm selected example | 400 mm selected example |
Payload scope | 12 kg maximum for the named configuration | 5 kg maximum for the named configuration |
Z stroke and downforce | Confirm exact spindle and stroke option | Confirm exact spindle and stroke option |
Tool pitch and roll | No independent six-axis pitch/roll | No independent six-axis pitch/roll |
Acceptance path | Same transfer, insert, rotate and settle sequence | Same transfer, insert, rotate and settle sequence |
Precision and throughput: compare the same task
The comparison uses ±0.012 mm (XY) for Mitsubishi Electric RH-12FH and ±0.01 mm (XY) for Shibaura Machine THE400. These figures should be read in their documented configuration scope. Repeatability is not absolute accuracy, camera calibration accuracy or finished-part capability. Fixture variation, TCP calibration, thermal conditions and tool compliance can dominate the error at the process point, especially when the tool extends far from the flange.
Ask each integrator to execute the same representative path with the same payload model, tool length, process dwell and stop conditions. Report transfer time, settling time, process time and waiting time separately. Published standard cycles often use different loads and distances; dividing one catalogue cycle by another would not establish the production advantage of Mitsubishi Electric RH-12FH over Shibaura Machine THE400. Use a measured or validated application cycle before assigning a throughput benefit.
Programming, controls and production integration
Mitsubishi Electric RH-12FH is paired here with Matched CR750/CR751 F-generation package; exact selected arm specification, while Shibaura Machine THE400 uses TSL3000 / matched TS5000 option. Controller names identify the review baseline rather than a guarantee that all interface options are included. Compare the actual software revision, teaching workflow, diagnostic tools, fieldbus licences and recovery procedures. An existing trained team and reusable production code may outweigh a small dimensional advantage. Obtain a demonstration of the same machine handshake and interrupted-cycle recovery on both platforms.
Specify the PLC handshakes before ordering: cycle request, ready, busy, complete, fault, part present and recovery authorization. Define how an interrupted operation resumes without repeating a dangerous or quality-critical action. Vision, force sensing, fieldbus communication and external-axis coordination must be checked as explicit included or optional functions. An Ethernet connector does not by itself prove that a particular industrial protocol or software interface is licensed and supported.
Configuration and communication detail
Integration reference | Mitsubishi Electric RH-12FH | Shibaura Machine THE400 |
|---|---|---|
Control package | Matched CR750/CR751 F-generation package; exact selected arm specification | TSL3000 / matched TS5000 option |
Documented interface baseline | Specify required interfaces in the delivered package | Specify required interfaces in the delivered package |
Programming baseline | Named platform software and supported API; confirm supplied version | Named platform software and supported API; confirm supplied version |
Integration acceptance | Test the actual machine handshake and controlled recovery | Test the same handshake and controlled recovery |
Protection, installation and maintenance
Match the precise protection package to the process. Standard, protected, cleanroom, foundry and washing configurations can have different seals, services and maintenance requirements. Do not transfer the best optional IP or cleanroom rating to an unprotected base model. Check the controller location, cable bend radius, available lifting access and base reactions with the installer.
Treat safe operation as a property of the complete task and installation. Include the tool, sharp workpiece edges, trapping points, dropped loads and machine access. These robot systems require task-specific safeguarding; payload or compact size does not establish safe unguarded operation. Plan tool replacement and fault recovery without dismantling the whole installation, and include connector access, lubrication and spare-cable replacement in the maintenance layout.
Price and lifecycle value
Request configuration-specific quotations for Mitsubishi Electric RH-12FH and Shibaura Machine THE400. An arm-only number is not the price of a commissioned production cell. Ask for separate line items for controller, pendant, communication options, end effector, safety equipment, installation, acceptance, training and warranty. Price changes, regional support and included software can reverse an apparent hardware-cost advantage. Compare the same delivered scope before calculating payback.
Compare the installed production scope: tool, fixtures, sensing, guarding, machine interface, programming, acceptance and training. For small-parts automation, include feeders, vision calibration, nests and rejected-part handling. Keep purchase cost and recurring support costs separate. No payback figure is defensible until the actual cycle, yield, utilization and installation quotation are known.
Selection and acceptance plan
Decision gate | Mitsubishi Electric RH-12FH | Shibaura Machine THE400 |
|---|---|---|
Strongest documented fit | 12 kg planar handling within the selected 550 mm SCARA envelope | 5 kg planar handling within the selected 400 mm SCARA envelope |
Main boundary | Tool mass, wrist moments and access constrain the headline specification. | Four axes do not provide arbitrary wrist pitch and roll. |
Required approval | Exact Mitsubishi Electric variant, tool load and validated process path | Exact competitor revision, tool load and validated process path |
Acceptance evidence | Agreed parts, path, quality and recovery results | The same agreed parts, path, quality and recovery results |
Advance Mitsubishi Electric RH-12FH when 12 kg planar handling within the selected 550 mm SCARA envelope solves the real constraint and its selected configuration passes the load and access checks. Advance Shibaura Machine THE400 when 5 kg planar handling within the selected 400 mm SCARA envelope provides the more suitable process arrangement. Reject either candidate if a mandatory pose, protection requirement or controller function cannot be demonstrated. A purchasing shortlist should preserve these conditions instead of converting a single catalogue advantage into a blanket recommendation.
Before acceptance, agree the representative parts, tool states, operating sequence and quality criteria with both suppliers. Demonstrate cold start, normal production, rejected parts, interrupted cycles and controlled recovery. Record the final tool data and software backup. This turns the comparison into a repeatable purchasing decision and helps prevent a later fixture change from invalidating the original robot selection.
Motion architecture and functionality
Mitsubishi Electric RH-12FH has 4 arm axes and Shibaura Machine THE400 has 4 arm axes. A four-axis mechanism cannot independently supply every pitch and roll angle. Assess whether the tool must stay level or be presented at varying attitudes. Compare tool detection, sensing, machine I/O and recovery as separate delivered functions.
Industries and application fit
For Mitsubishi Electric RH-12FH vs Shibaura Machine THE400, use the actual part and process as the industry filter. Electronics assembly, component packaging and small mechanical assembly are plausible candidates when the required movement is primarily horizontal transfer plus vertical insertion. These are application-selection judgments, not claims that either exact model is installed at a named customer. A food, medical-device or clean-production application additionally requires the correct material, lubrication and protection package; the base model name does not establish hygienic or cleanroom compliance.
Selection issue | Mitsubishi Electric RH-12FH | Shibaura Machine THE400 |
|---|---|---|
Tool and workpiece mass | 12 kg named scope; include the complete tool | 5 kg named scope; include the complete tool |
Working reference | 550 mm | 400 mm |
Main configuration boundary | Tool mass, wrist moments and access constrain the headline specification. | Four axes do not provide arbitrary wrist pitch and roll. |
Process approval | Demonstrate the actual loaded path and recovery | Demonstrate the same loaded path and recovery |
Frequently asked questions
Which robot is better for this application?
Mitsubishi Electric RH-12FH is the stronger starting point for 12 kg planar handling within the selected 550 mm SCARA envelope, while Shibaura Machine THE400 is worth shortlisting for 5 kg planar handling within the selected 400 mm SCARA envelope. The final choice depends on the real loaded path, required protection, controls and acceptance results. Neither a higher payload nor a longer reach establishes a universal winner.
What payload should I use for the comparison?
Use 12 kg for the specified Mitsubishi Electric RH-12FH5535-D example and 5 kg for Shibaura Machine THE400, subject to all documented load and orientation conditions. Include the tool, adapters, sensors and carried part. Four axes do not provide arbitrary wrist pitch and roll.
Does the stated reach guarantee access to my fixture?
No. The comparison gives 550 mm for Mitsubishi Electric RH-12FH and 400 mm for Shibaura Machine THE400 using the stated model references. Joint limits, reach reference points, wrist orientation, tool length and collisions determine whether the actual fixture is accessible. Simulate the full approach and exit path.
Can I use the best specifications from every family variant?
No. Keep each named model and revision intact. A different arm length, controller generation or protection option can change the relevant specification. Do not combine one version’s maximum payload with another version’s maximum reach.
Is repeatability the same as finished-part accuracy?
No. The stated values are ±0.012 mm (XY) for Mitsubishi Electric RH-12FH scope and ±0.01 mm (XY) for the competitor scope. Finished-part results also depend on fixtures, TCP calibration, sensing, thermal conditions and tool compliance. Validate the actual process instead of treating catalogue repeatability as a complete accuracy guarantee.
How should purchase prices be compared?
Use current written quotations for Mitsubishi Electric RH-12FH and Shibaura Machine THE400 with the same arm, controller, software, tooling and commissioning scope. This comparison does not represent an ATC sales offer or stock confirmation. Historical review figures are not a substitute for a configuration-specific purchase quotation.
Can these robots operate safely next to people without guarding?
These specifications do not establish a safe unguarded installation. Assess the complete task, tool, load and machine interface, then implement and validate the required safeguarding and operating procedures. Do not infer collaborative operation from a compact arm, limited payload or education setting.
What should an acceptance test compare?
Use the same parts, actual tool load, fixture locations, path and quality criteria for Mitsubishi Electric RH-12FH and Shibaura Machine THE400. Check production timing, settling, interruptions and recovery. Include the most difficult loaded approach and retreat. Approve the exact delivered configuration and preserve its final settings.
Related ATC reviews
Specifications describe the model scope identified above. Purchase pricing requires a current configuration-specific quotation. Confirm current manufacturer documentation, local supply, controller compatibility and the exact configuration before purchase.
