FANUC M-410iC/315 vs Nachi LP130F: Robot Comparison
Updated: 3 hours ago
IN A NUTSHELL
🔎 THE KEY DIFFERENCE This is a load-versus-reach trade-off: FANUC M-410iC/315 has the higher stated load capacity, while Nachi LP130F has the longer stated reach. Start with the constraint your task actually has. |
→ CONSIDER FANUC M-410iC/315 Consider it when additional load capacity matters more than extra reach. This article compares 315 kg and a 3,143 mm stated reach; include the gripper and part in the load. |
→ CONSIDER Nachi LP130F Consider it when reaching farther matters more than the higher payload of the alternative. This article compares 130 kg and a 3,210 mm stated reach; include the gripper and part in the load. |
💡 THE TAKEAWAY Choose the robot that handles your actual tool and part through the required path, with controls and support your team can use. Compare complete installation quotes, rather than arm-only prices. |
FANUC M-410iC/315 vs Nachi LP130F is a choice about palletizing and load orientation. FANUC M-410iC/315 and Nachi LP130F differ in their working envelope, loading assumptions and engineering ecosystem. A useful decision starts with the exact mechanism and process, then checks whether either robot can execute the required path with the real tool attached. This comparison separates documented specifications from application-level engineering judgments.
FANUC M-410iC/315 vs Nachi LP130F: quick verdict
Shortlist FANUC M-410iC/315 for 315 kg palletizing within the named 3143 mm envelope and 4-axis architecture. Shortlist Nachi LP130F for 130 kg palletizing within the named 3210 mm envelope and 4-axis architecture. First decide whether the product stays level or must be tilted. A payload match does not remove an architectural difference between four and six axes.
The numerical comparison below uses FANUC M-410iC/315 against Nachi LP130F. The stated model scope matters when comparing later revisions or differently equipped installations. Published repeatability describes return to a taught position under specified conditions; it does not establish complete-cell accuracy or prove a faster production cycle.
Specifications and exact configuration scope
Criterion | FANUC M-410iC/315 | Nachi LP130F |
|---|---|---|
Comparison configuration | FANUC M-410iC/315 | Nachi LP130F |
Payload used for comparison | 315 kg | 130 kg |
Reach / motion-area reference | 3143 mm | 3210 mm |
Axes | 4 | 4 |
Repeatability for this scope | ±0.05 mm | ±0.09 mm |
Controller reference | R-30iB Plus package; verify cabinet and supplied generation | the supplied model-specific control package |
Purchase-price basis | Configuration-specific quotation | Configuration-specific quotation |
Purchase pricing | From $95,000 (arm list price) | From $44,000 (arm list price) |
Read the reach row together with the geometric notes below. Manufacturers may specify an arm-link sum, a wrist-centre motion area or reach to the flange; those dimensions are not interchangeable. The table does not establish access to every point at every tool angle. Controller references identify reviewed packages, and actual compatibility must be confirmed by model, software version and region.
FANUC M-410iC/315: design and configuration
The FANUC M-410iC/315 is the named 4-axis configuration with 315 kg payload, 3143 mm horizontal reach and ±0.05 mm repeatability in the reviewed model scope. This is a four-axis palletizing mechanism for positioning and rotating a level load. It cannot independently provide every pitch and roll attitude of a six-axis wrist. Count the complete gripper, retained product and cable services, then check the highest layer, farthest corner and load retention during stops. Catalogue payload does not approve every layer-gripper inertia. The control baseline is R-30iB Plus package; verify cabinet and supplied generation; cabinet, industrial-network licences, safety options and process software must be named in the quotation.
Nachi LP130F: design and configuration
The Nachi LP130F is a 4-axis palletizing robot with a 130 kg payload, a reach of 3210 mm and a position repeatability of ±0.09 mm. A large-capacity motor and optimized motion control give it high-speed palletizing of heavy loads. It stacks pallets up to 1600 mm square to a height of 2212 mm, and the forearm carries up to 25 kg of additional equipment. The arm weighs 1150 kg and is designed for floor mounting. The LP130F runs on a Nachi robot controller and is programmed from the Nachi teach pendant. Nachi's FD on Desk software is available for offline programming and simulation. The controller, end effectors, safety equipment and integration affect the final price and are quoted separately. Prices are indicative, are not final and may change.
For this pair, Nachi LP130F offers 130 kg over the stated 3210 mm reference, compared with 315 kg and 3143 mm for FANUC M-410iC/315 example. Nachi LP130F has the larger stated distance by 67 mm, but this difference is only a preliminary layout indicator because reference points and joint envelopes can differ. Locate the actual fixture in each manufacturer model before treating this as usable extra working space.
Payload, tooling and a worked load example
Consider an illustrative total wrist load of 104 kg: a 26 kg tool and adapter package carrying a 78 kg part or product group. This arithmetic leaves 211 kg below the FANUC M-410iC/315 example’s nominal limit and 26 kg below Nachi LP130F’s nominal limit. These are mass differences, not safety factors or a validated load approval. A heavy camera, valve block or retained material must be included before recalculating the total.
The example exposes the practical question: is the application limited by mass, by tool offset or by wrist rotation? Nachi LP130F is the lower-or-equal nominal payload choice in this pair. FANUC M-410iC/315 offers more or equal headline mass capacity, but that alone cannot approve an eccentric fixture. Moving the same mass farther from the flange increases the moment, and spreading it increases rotational inertia. Manufacturer load diagrams and the actual centre of gravity govern the final allowable motion.
Model the empty, partly loaded and fully loaded tool states separately. A vacuum layer gripper, a weld torch with hoses or an inspection head may change its effective loading during the cycle. Set the controller’s load data for each supported state and validate the transition logic. A payload table cannot predict acceleration derating, cable pull or transient reactions at a machine interface.
Reach, orientation and fixture access
Build the same cell model for both candidates: base height, machine opening, fixture datum, maximum part size, tool extension and access for maintenance. FANUC M-410iC/315 provides a stated 3143 mm reference, while Nachi LP130F provides 3210 mm. Check the deepest production pose and the return path with the loaded tool. An arm that just touches the target at full extension may have little freedom left to turn, retract or avoid a door.
For this comparison, distinguish level-load palletizing from general reorientation. Four-axis palletizers can position and rotate a level product around the vertical axis, but cannot independently supply every pitch and roll angle. A six-axis arm may support tilted presentation or recovery, yet it must be assessed on the same pallet pattern and load. Check the lowest pickup, highest layer, farthest corner and safe exit path.
Precision and throughput: compare the same task
The comparison uses ±0.05 mm for FANUC M-410iC/315 and ±0.09 mm for Nachi LP130F. These figures should be read in their documented configuration scope. Repeatability is not absolute accuracy, camera calibration accuracy or finished-part capability. Fixture variation, TCP calibration, thermal conditions and tool compliance can dominate the error at the process point, especially when the tool extends far from the flange.
Ask each integrator to execute the same representative path with the same payload model, tool length, process dwell and stop conditions. Report transfer time, settling time, process time and waiting time separately. Published standard cycles often use different loads and distances; dividing one catalogue cycle by another would not establish the production advantage of FANUC M-410iC/315 over Nachi LP130F. Use a measured or validated application cycle before assigning a throughput benefit.
Programming, controls and production integration
FANUC M-410iC/315 is paired here with R-30iB Plus package; verify cabinet and supplied generation, while Nachi LP130F uses the supplied model-specific control package. Controller names identify the review baseline rather than a guarantee that all interface options are included. Compare the actual software revision, teaching workflow, diagnostic tools, fieldbus licences and recovery procedures. An existing trained team and reusable production code may outweigh a small dimensional advantage. Obtain a demonstration of the same machine handshake and interrupted-cycle recovery on both platforms.
Specify the PLC handshakes before ordering: cycle request, ready, busy, complete, fault, part present and recovery authorization. Define how an interrupted operation resumes without repeating a dangerous or quality-critical action. Vision, force sensing, fieldbus communication and external-axis coordination must be checked as explicit included or optional functions. An Ethernet connector does not by itself prove that a particular industrial protocol or software interface is licensed and supported.
Configuration and communication detail
Integration reference | FANUC M-410iC/315 | Nachi LP130F |
|---|---|---|
Control package | R-30iB Plus package; verify cabinet and supplied generation | the supplied model-specific control package |
Documented interface baseline | Specify required interfaces in the delivered package | Specify required interfaces in the delivered package |
Programming baseline | Named platform software and supported API; confirm supplied version | Named platform software and supported API; confirm supplied version |
Integration acceptance | Test the actual machine handshake and controlled recovery | Test the same handshake and controlled recovery |
Protection, installation and maintenance
Match the precise protection package to the process. Standard, protected, cleanroom, foundry and washing configurations can have different seals, services and maintenance requirements. Do not transfer the best optional IP or cleanroom rating to an unprotected base model. Check the controller location, cable bend radius, available lifting access and base reactions with the installer.
Treat safe operation as a property of the complete task and installation. Include the tool, sharp workpiece edges, trapping points, dropped loads and machine access. These robot systems require task-specific safeguarding; payload or compact size does not establish safe unguarded operation. Plan tool replacement and fault recovery without dismantling the whole installation, and include connector access, lubrication and spare-cable replacement in the maintenance layout.
Price and lifecycle value
Published arm list prices: FANUC M-410iC/315 is listed from $95,000 and Nachi LP130F is listed from $44,000. Request configuration-specific quotations for FANUC M-410iC/315 and Nachi LP130F. An arm-only number is not the price of a commissioned production cell. Ask for separate line items for controller, pendant, communication options, end effector, safety equipment, installation, acceptance, training and warranty. Price changes, regional support and included software can reverse an apparent hardware-cost advantage. Compare the same delivered scope before calculating payback.
Compare the installed production scope: tool, fixtures, sensing, guarding, machine interface, programming, acceptance and training. For palletizing, include infeed control, pallet detection, load retention and gripper services. Keep purchase cost and recurring support costs separate. No payback figure is defensible until the actual cycle, yield, utilization and installation quotation are known.
Selection and acceptance plan
Decision gate | FANUC M-410iC/315 | Nachi LP130F |
|---|---|---|
Strongest documented fit | 315 kg palletizing within the named 3143 mm envelope and 4-axis architecture | 130 kg palletizing within the named 3210 mm envelope and 4-axis architecture |
Main boundary | Four arm axes position and rotate a level load; they do not provide arbitrary pitch and roll. Validate complete gripper inertia, load retention and the full pallet pattern. | Four arm axes position and rotate a level load; they do not provide arbitrary pitch and roll. Validate complete gripper inertia, load retention and the full pallet pattern. |
Required approval | Exact FANUC variant, tool load and validated process path | Exact competitor revision, tool load and validated process path |
Acceptance evidence | Agreed parts, path, quality and recovery results | The same agreed parts, path, quality and recovery results |
Advance FANUC M-410iC/315 when 315 kg palletizing within the named 3143 mm envelope and 4-axis architecture solves the real constraint and its selected configuration passes the load and access checks. Advance Nachi LP130F when 130 kg palletizing within the named 3210 mm envelope and 4-axis architecture provides the more suitable process arrangement. Reject either candidate if a mandatory pose, protection requirement or controller function cannot be demonstrated. A purchasing shortlist should preserve these conditions instead of converting a single catalogue advantage into a blanket recommendation.
Before acceptance, agree the representative parts, tool states, operating sequence and quality criteria with both suppliers. Demonstrate cold start, normal production, rejected parts, interrupted cycles and controlled recovery. Record the final tool data and software backup. This turns the comparison into a repeatable purchasing decision and helps prevent a later fixture change from invalidating the original robot selection.
Motion architecture and functionality
FANUC M-410iC/315 has 4 arm axes and Nachi LP130F has 4 arm axes. A four-axis mechanism cannot independently supply every pitch and roll angle. Assess whether the tool must stay level or be presented at varying attitudes. Compare tool detection, sensing, machine I/O and recovery as separate delivered functions.
Industries and application fit
For FANUC M-410iC/315 vs Nachi LP130F, use the actual part and process as the industry filter. Electronics, manufactured-component handling and machine tending are candidate uses when their tool mass, access and quality requirements fit the documented configurations. These are application-selection judgments, not claims that either exact model is installed at a named customer. A food, medical-device or clean-production application additionally requires the correct material, lubrication and protection package; the base model name does not establish hygienic or cleanroom compliance.
Selection issue | FANUC M-410iC/315 | Nachi LP130F |
|---|---|---|
Tool and workpiece mass | 315 kg named scope; include the complete tool | 130 kg named scope; include the complete tool |
Working reference | 3143 mm | 3210 mm |
Main configuration boundary | Four arm axes position and rotate a level load; they do not provide arbitrary pitch and roll. Validate complete gripper inertia, load retention and the full pallet pattern. | Four arm axes position and rotate a level load; they do not provide arbitrary pitch and roll. Validate complete gripper inertia, load retention and the full pallet pattern. |
Process approval | Demonstrate the actual loaded path and recovery | Demonstrate the same loaded path and recovery |
Frequently asked questions
Which robot is better for this application?
FANUC M-410iC/315 is the stronger starting point for 315 kg palletizing within the named 3143 mm envelope and 4-axis architecture, while Nachi LP130F is worth shortlisting for 130 kg palletizing within the named 3210 mm envelope and 4-axis architecture. The final choice depends on the real loaded path, required protection, controls and acceptance results. Neither a higher payload nor a longer reach establishes a universal winner.
What payload should I use for the comparison?
Use 315 kg for the specified FANUC M-410iC/315 example and 130 kg for Nachi LP130F, subject to all documented load and orientation conditions. Include the tool, adapters, sensors and carried part. Four arm axes position and rotate a level load; they do not provide arbitrary pitch and roll. Validate complete gripper inertia, load retention and the full pallet pattern.
Does the stated reach guarantee access to my fixture?
No. The comparison gives 3143 mm for FANUC M-410iC/315 and 3210 mm for Nachi LP130F using the stated model references. Joint limits, reach reference points, wrist orientation, tool length and collisions determine whether the actual fixture is accessible. Simulate the full approach and exit path.
Can I use the best specifications from every family variant?
No. Keep each named model and revision intact. A different arm length, controller generation or protection option can change the relevant specification. Do not combine one version’s maximum payload with another version’s maximum reach.
Is repeatability the same as finished-part accuracy?
No. The stated values are ±0.05 mm for FANUC M-410iC/315 scope and ±0.09 mm for the competitor scope. Finished-part results also depend on fixtures, TCP calibration, sensing, thermal conditions and tool compliance. Validate the actual process instead of treating catalogue repeatability as a complete accuracy guarantee.
How should purchase prices be compared?
Use current written quotations for FANUC M-410iC/315 and Nachi LP130F with the same arm, controller, software, tooling and commissioning scope. This comparison does not represent an ATC sales offer or stock confirmation. Historical review figures are not a substitute for a configuration-specific purchase quotation.
Can these robots operate safely next to people without guarding?
These specifications do not establish a safe unguarded installation. Assess the complete task, tool, load and machine interface, then implement and validate the required safeguarding and operating procedures. Do not infer collaborative operation from a compact arm, limited payload or education setting.
What should an acceptance test compare?
Use the same parts, actual tool load, fixture locations, path and quality criteria for FANUC M-410iC/315 and Nachi LP130F. Check production timing, settling, interruptions and recovery. Include the highest layer and farthest pallet corner. Approve the exact delivered configuration and preserve its final settings.
Related ATC reviews
Specifications describe the model scope identified above. Purchase pricing requires a current configuration-specific quotation. Confirm current manufacturer documentation, local supply, controller compatibility and the exact configuration before purchase.
