FANUC ARC Mate 100iD vs Panasonic TS Series: Robot Comparison

IN A NUTSHELL

FANUC ARC Mate 100iD vs Panasonic TS Series is a choice about arc welding and process access. FANUC ARC Mate 100iD and Panasonic TS Series differ in their working envelope, loading assumptions and engineering ecosystem. A useful decision starts with the exact mechanism and process, then checks whether either robot can execute the required path with the real tool attached. This comparison separates documented specifications from application-level engineering judgments.

FANUC ARC Mate 100iD vs Panasonic TS Series: quick verdict

Shortlist FANUC ARC Mate 100iD for arc-welding access using the named 12 kg / 1441 mm process-arm configuration. Shortlist Panasonic TS Series for arc-welding access using the named 8 kg / 841 mm process-arm configuration. Neither is a universal winner: a robot that can carry the load may still fail the fixture-access, controller or maintenance requirements.

The numerical comparison below uses FANUC ARC Mate 100iD against Panasonic TS Series. The stated model scope matters when comparing later revisions or differently equipped installations. Published repeatability describes return to a taught position under specified conditions; it does not establish complete-cell accuracy or prove a faster production cycle.

Specifications and exact configuration scope

Read the reach row together with the geometric notes below. Manufacturers may specify an arm-link sum, a wrist-centre motion area or reach to the flange; those dimensions are not interchangeable. The table does not establish access to every point at every tool angle. Controller references identify reviewed packages, and actual compatibility must be confirmed by model, software version and region.

FANUC ARC Mate 100iD: design and configuration

The FANUC ARC Mate 100iD is the named 6-axis configuration with 12 kg payload, 1441 mm horizontal reach and ±0.02 mm repeatability in the reviewed model scope. The dedicated arc-welding geometry and internal torch-service routing matter when approaching seams. Include torch angle, wire feed, cable dressing, power-source communication and interrupted-weld recovery. A handling robot with similar payload is not automatically the same welding package. The control baseline is R-30iB Plus package; verify cabinet and supplied generation; cabinet, industrial-network licences, safety options and process software must be named in the quotation.

Panasonic TS Series: design and configuration

The Panasonic TS Series comparison uses one fixed six-axis reference: TS800, 8 kg payload, 841 mm reach and ±0.05 mm repeatability. Family names cover several distinct arm lengths and wrist limits; the numerical example never combines their maxima. The arm is a welding manipulator, not a complete weld process. Match the supplied G-series controller revision, power source, torch, wire feed, cooling and selected arc or touch-sensing functions. An externally routed torch package and an internally routed package have different service and clearance requirements. Gun or torch cabling adds load and restricts the working envelope even when the wrist mass remains inside the headline rating. Check approach angles, seam endpoints, recovery after arc failure, dress-pack fatigue and access for consumables. Repeatable flange motion does not establish weld penetration or joint quality. Qualify the actual material, joint preparation, weld procedure and fixture stiffness, then measure the complete loaded cycle rather than inferring production rate from a joint-speed figure.

For this pair, Panasonic TS Series offers 8 kg over the stated 841 mm reference, compared with 12 kg and 1441 mm for FANUC ARC Mate 100iD example. FANUC ARC Mate 100iD has the larger stated distance by 600 mm, but this difference is only a preliminary layout indicator because reference points and joint envelopes can differ. Locate the actual fixture in each manufacturer model before treating this as usable extra working space.

Payload, tooling and a worked load example

Consider an illustrative total wrist load of 6.4 kg: a 1.6 kg tool and adapter package carrying a 4.8 kg part or product group. This arithmetic leaves 5.6 kg below the FANUC ARC Mate 100iD example’s nominal limit and 1.6 kg below Panasonic TS Series’s nominal limit. These are mass differences, not safety factors or a validated load approval. A heavy camera, valve block or retained material must be included before recalculating the total.

The example exposes the practical question: is the application limited by mass, by tool offset or by wrist rotation? Panasonic TS Series is the lower-or-equal nominal payload choice in this pair. FANUC ARC Mate 100iD offers more or equal headline mass capacity, but that alone cannot approve an eccentric fixture. Moving the same mass farther from the flange increases the moment, and spreading it increases rotational inertia. Manufacturer load diagrams and the actual centre of gravity govern the final allowable motion.

Model the empty, partly loaded and fully loaded tool states separately. A vacuum layer gripper, a weld torch with hoses or an inspection head may change its effective loading during the cycle. Set the controller’s load data for each supported state and validate the transition logic. A payload table cannot predict acceleration derating, cable pull or transient reactions at a machine interface.

Reach, orientation and fixture access

Build the same cell model for both candidates: base height, machine opening, fixture datum, maximum part size, tool extension and access for maintenance. FANUC ARC Mate 100iD provides a stated 1441 mm reference, while Panasonic TS Series provides 841 mm. Check the deepest production pose and the return path with the loaded tool. An arm that just touches the target at full extension may have little freedom left to turn, retract or avoid a door.

For the welding comparison, include the actual torch angle, nozzle length, seam approach and cable package. Simulate seam starts and ends as well as continuous travel. A pose that looks accessible with an empty flange may become blocked after the torch, wire feeder and fixtures are installed. Validate touch sensing or seam-tracking options only where they are part of the supplied package.

Precision and throughput: compare the same task

The comparison uses ±0.02 mm for FANUC ARC Mate 100iD and ±0.05 mm for Panasonic TS Series. These figures should be read in their documented configuration scope. Repeatability is not absolute accuracy, camera calibration accuracy or finished-part capability. Fixture variation, TCP calibration, thermal conditions and tool compliance can dominate the error at the process point, especially when the tool extends far from the flange.

Ask each integrator to execute the same representative path with the same payload model, tool length, process dwell and stop conditions. Report transfer time, settling time, process time and waiting time separately. Published standard cycles often use different loads and distances; dividing one catalogue cycle by another would not establish the production advantage of FANUC ARC Mate 100iD over Panasonic TS Series. Use a measured or validated application cycle before assigning a throughput benefit.

Programming, controls and production integration

FANUC ARC Mate 100iD is paired here with R-30iB Plus package; verify cabinet and supplied generation, while Panasonic TS Series uses the supplied model-specific control package. Controller names identify the review baseline rather than a guarantee that all interface options are included. Compare the actual software revision, teaching workflow, diagnostic tools, fieldbus licences and recovery procedures. An existing trained team and reusable production code may outweigh a small dimensional advantage. Obtain a demonstration of the same machine handshake and interrupted-cycle recovery on both platforms.

Specify the PLC handshakes before ordering: cycle request, ready, busy, complete, fault, part present and recovery authorization. Define how an interrupted operation resumes without repeating a dangerous or quality-critical action. Vision, force sensing, fieldbus communication and external-axis coordination must be checked as explicit included or optional functions. An Ethernet connector does not by itself prove that a particular industrial protocol or software interface is licensed and supported.

Configuration and communication detail

Protection, installation and maintenance

Match the precise protection package to the process. Standard, protected, cleanroom, foundry and washing configurations can have different seals, services and maintenance requirements. Do not transfer the best optional IP or cleanroom rating to an unprotected base model. Check the controller location, cable bend radius, available lifting access and base reactions with the installer.

Treat safe operation as a property of the complete task and installation. Include the tool, sharp workpiece edges, trapping points, dropped loads and machine access. These robot systems require task-specific safeguarding; payload or compact size does not establish safe unguarded operation. Plan tool replacement and fault recovery without dismantling the whole installation, and include connector access, lubrication and spare-cable replacement in the maintenance layout.

Price and lifecycle value

Published arm list prices: FANUC ARC Mate 100iD is listed from $38,000. Request configuration-specific quotations for FANUC ARC Mate 100iD and Panasonic TS Series. An arm-only number is not the price of a commissioned production cell. Ask for separate line items for controller, pendant, communication options, end effector, safety equipment, installation, acceptance, training and warranty. Price changes, regional support and included software can reverse an apparent hardware-cost advantage. Compare the same delivered scope before calculating payback.

Compare the installed production scope: tool, fixtures, sensing, guarding, machine interface, programming, acceptance and training. For welding, include the power source, wire feed, torch cleaning, extraction and seam options. Keep purchase cost and recurring support costs separate. No payback figure is defensible until the actual cycle, yield, utilization and installation quotation are known.

Selection and acceptance plan

Advance FANUC ARC Mate 100iD when arc-welding access using the named 12 kg / 1441 mm process-arm configuration solves the real constraint and its selected configuration passes the load and access checks. Advance Panasonic TS Series when arc-welding access using the named 8 kg / 841 mm process-arm configuration provides the more suitable process arrangement. Reject either candidate if a mandatory pose, protection requirement or controller function cannot be demonstrated. A purchasing shortlist should preserve these conditions instead of converting a single catalogue advantage into a blanket recommendation.

Before acceptance, agree the representative parts, tool states, operating sequence and quality criteria with both suppliers. Demonstrate cold start, normal production, rejected parts, interrupted cycles and controlled recovery. Record the final tool data and software backup. This turns the comparison into a repeatable purchasing decision and helps prevent a later fixture change from invalidating the original robot selection.

Motion architecture and functionality

FANUC ARC Mate 100iD has 6 arm axes and Panasonic TS Series has 6 arm axes. Both have six arm axes; equal axis counts do not establish equal joint travel, inner workspace or fixture access. Compare tool detection, sensing, machine I/O and recovery as separate delivered functions.

Industries and application fit

For FANUC ARC Mate 100iD vs Panasonic TS Series, use the actual part and process as the industry filter. Electronics, manufactured-component handling and machine tending are candidate uses when their tool mass, access and quality requirements fit the documented configurations. These are application-selection judgments, not claims that either exact model is installed at a named customer. A food, medical-device or clean-production application additionally requires the correct material, lubrication and protection package; the base model name does not establish hygienic or cleanroom compliance.

Frequently asked questions

Which robot is better for this application?

FANUC ARC Mate 100iD is the stronger starting point for arc-welding access using the named 12 kg / 1441 mm process-arm configuration, while Panasonic TS Series is worth shortlisting for arc-welding access using the named 8 kg / 841 mm process-arm configuration. The final choice depends on the real loaded path, required protection, controls and acceptance results. Neither a higher payload nor a longer reach establishes a universal winner.

What payload should I use for the comparison?

Use 12 kg for the specified FANUC ARC Mate 100iD example and 8 kg for Panasonic TS Series, subject to all documented load and orientation conditions. Include the tool, adapters, sensors and carried part. Torch, cables, wire feed, power-source interface and seam recovery must match the quoted package; arm geometry does not supply a complete welding cell.

Does the stated reach guarantee access to my fixture?

No. The comparison gives 1441 mm for FANUC ARC Mate 100iD and 841 mm for Panasonic TS Series using the stated model references. Joint limits, reach reference points, wrist orientation, tool length and collisions determine whether the actual fixture is accessible. Simulate the full approach and exit path.

Can I use the best specifications from every family variant?

No. Keep each named model and revision intact. A different arm length, controller generation or protection option can change the relevant specification. Do not combine one version’s maximum payload with another version’s maximum reach.

Is repeatability the same as finished-part accuracy?

No. The stated values are ±0.02 mm for FANUC ARC Mate 100iD scope and ±0.05 mm for the competitor scope. Finished-part results also depend on fixtures, TCP calibration, sensing, thermal conditions and tool compliance. Validate the actual process instead of treating catalogue repeatability as a complete accuracy guarantee.

How should purchase prices be compared?

Use current written quotations for FANUC ARC Mate 100iD and Panasonic TS Series with the same arm, controller, software, tooling and commissioning scope. This comparison does not represent an ATC sales offer or stock confirmation. Historical review figures are not a substitute for a configuration-specific purchase quotation.

Can these robots operate safely next to people without guarding?

These specifications do not establish a safe unguarded installation. Assess the complete task, tool, load and machine interface, then implement and validate the required safeguarding and operating procedures. Do not infer collaborative operation from a compact arm, limited payload or education setting.

What should an acceptance test compare?

Use the same parts, actual tool load, fixture locations, path and quality criteria for FANUC ARC Mate 100iD and Panasonic TS Series. Check production timing, settling, interruptions and recovery. Include seam access and the supplied welding functions. Approve the exact delivered configuration and preserve its final settings.

Related ATC reviews

Read the FANUC ARC Mate 100iD review

Read the Panasonic TS Series review

Specifications describe the model scope identified above. Purchase pricing requires a current configuration-specific quotation. Confirm current manufacturer documentation, local supply, controller compatibility and the exact configuration before purchase.