Comau MyCo-15-1.30 Review: Specs, Uses, Pros & Cons
Comau MyCo-15-1.30 review: Model — MyCo-15-1.30. Axes — 6. This guide examines the documented configuration, practical engineering tradeoffs and the buying questions that matter for a successful installation.
Quick Verdict
A useful collaborative robot for applications that genuinely fit its 15 kg wrist limit and 1300 mm reach. Its value depends on tool selection, fixture access and the complete validated cycle rather than the robot-only specification.
Technical Specifications
Technical field | Documented configuration / buying implication |
|---|---|
Model | MyCo-15-1.30 |
Axes | 6 |
Maximum wrist payload | 15 kg |
Maximum horizontal reach | 1300 mm |
Robot weight | 60 kg |
Repeatability | ±0.05 mm |
Typical application consumption | 600 W; not peak input |
Protection | IP54; IP66 option described in family brochure |
Price | Request a configuration-specific quotation |
Design and Engineering Assessment
Larger tooling and longer transfers are its natural territory. The 15 kg allowance must include the gripper and carried fixtures; a long offset tool can reach a wrist-moment limit before reaching the payload limit. Comau describes graphical programming and a remote calling interface, while optional fieldbus functions should be named in the order. Fast installation of the arm does not remove machine interlocks, recovery programming or process qualification. Typical power figures describe an application example and must not be used as the electrical supply sizing limit.
Applications and Best-Fit Projects
Pallet-layer work with moderate loads, heavier machine tending and multi-part transfer. Compare the lighter 8 kg version if tooling and workpieces fit comfortably within that envelope.
Tooling, payload and useful workspace
Size the arm using the combined mass of gripper, adapters, carried part and moving process equipment. Then check center of gravity and wrist moments. A long tool can exceed a moment or inertia limit even when its total mass is below the payload rating. Validate approach and withdrawal poses, not just the final working point. Singularity avoidance, cable routing and tool clearance can reduce the usable area well inside a nominal reach circle.
Programming, controls and commissioning
A simple teaching interface helps create motion, but the production program must also handle missing parts, machine-not-ready signals, interrupted cycles and safe restart. Define the electrical and software boundary between the robot and surrounding equipment. Verify whether required industrial protocols are standard, licensed or supplied through an adapter. Maintain backed-up programs and documented tool, work-object and payload settings so a replacement controller or fixture adjustment does not silently change process behavior.
Safety and real cycle performance
Collaborative equipment does not make every installed task suitable for unguarded operation. Tool edges, trapped spaces, hot parts and the workpiece itself can dominate the risk. Validate the required safeguarding and stopping behavior for the complete application. Measure the actual cycle with representative loads, process dwell and human access. An unloaded maximum speed or joint limit does not predict a cycle that must slow down near people or wait for a machine.
Price, Value and What the Quote Should Include
Request a quotation for the exact configuration described in the technical table. Separate the base equipment from tooling, software options, installation, commissioning, training and ongoing service. Ask the supplier to identify the delivered revision and acceptance obligations in writing. A low hardware price is not a saving if the project requires unbudgeted integration or unsupported accessories.
For the value assessment, compare the present workflow with a realistic proposed cycle. Include the time people still spend loading, replenishing, checking quality and recovering faults. Estimate savings only from changes the proposed system can actually deliver. Keep maintenance, changeover and support availability in the calculation, and use a representative pilot to replace optimistic assumptions with measured results.
Pros and Cons
Strengths
• 15 kg defined wrist payload
• 1300 mm defined reach
• Graphical programming approach
Limits to Account For
• Tool inertia can constrain the application
• Collaborative cell speed needs validation
Commissioning and Acceptance Checklist
Validate the full tool-plus-part load, center of gravity, wrist moments and every approach pose. Measure settled process performance and stopping behavior at the actual 1300 mm station layout.
Write the required result, test conditions and pass/fail threshold before running acceptance. Include the least favorable normal load or part, a representative shift or operating sequence and the recovery cases that occur in the real workflow. Keep a record of the supplied hardware, software and settings so future maintenance can restore the same validated behavior.
Who Should Consider It
Pallet-layer work with moderate loads, heavier machine tending and multi-part transfer. Compare the lighter 8 kg version if tooling and workpieces fit comfortably within that envelope. A useful collaborative robot for applications that genuinely fit its 15 kg wrist limit and 1300 mm reach. Its value depends on tool selection, fixture access and the complete validated cycle rather than the robot-only specification.
Frequently Asked Questions
What is Comau MyCo-15-1.30 best suited to?
Pallet-layer work with moderate loads, heavier machine tending and multi-part transfer. Compare the lighter 8 kg version if tooling and workpieces fit comfortably within that envelope.
Which technical specifications matter most for Comau MyCo-15-1.30?
The documented starting points are Model: MyCo-15-1.30; Axes: 6; Maximum wrist payload: 15 kg. Match those values to one supplied configuration; do not combine family endpoints or assume an optional package is included.
How should Comau MyCo-15-1.30 be integrated into a real workflow?
Size the arm using the combined mass of gripper, adapters, carried part and moving process equipment. Define the task boundaries, handoff signals and exception states before commissioning. Verify them with the actual tooling, carriers, fixtures or site data rather than a simplified demonstration.
What are the main limitations of Comau MyCo-15-1.30?
The main constraints are tool inertia can constrain the application; collaborative cell speed needs validation. Larger tooling and longer transfers are its natural territory. Compare the complete installed solution against the process requirement rather than relying on a single headline figure.
What does Comau MyCo-15-1.30 cost?
Request a configuration-specific quotation. A verified fixed public price for the complete package is not established here. The proposal should identify included hardware, required software, integration, training, service and any recurring charges so competing quotations cover the same scope.
Can Comau MyCo-15-1.30 operate without human involvement?
Do not infer unattended reliability from a successful demonstration. Define which task steps are automated, which still require operators and how the system reacts to missing inputs, obstruction or process faults. Release only the validated operating envelope.
What should be tested before accepting Comau MyCo-15-1.30?
Validate the full tool-plus-part load, center of gravity, wrist moments and every approach pose. Measure settled process performance and stopping behavior at the actual 1300 mm station layout. Record measurable acceptance criteria and retain the results for the delivered configuration.
How should buyers compare Comau MyCo-15-1.30 with alternatives?
Use the same task, quality target, operating conditions and support horizon for each proposal. Its value depends on tool selection, fixture access and the complete validated cycle rather than the robot-only specification. Compare total installed and operating cost, including recovery effort and changeover, rather than robot-only price.
Specifications and included options depend on the ordered model and revision. Confirm the final configuration, commercial terms and local support with the supplier.
