ABB SWIFTI CRB 1300-11/0.9 vs FAIRINO FR10: Cobot Comparison
Updated: 13 hours ago
IN A NUTSHELL
🔎 THE KEY DIFFERENCE This is a load-versus-reach trade-off: ABB SWIFTI CRB 1300-11/0.9 has the higher stated load capacity, while FAIRINO FR10 has the longer stated reach. Start with the constraint your task actually has. |
→ CONSIDER ABB SWIFTI CRB 1300-11/0.9 Consider it when additional load capacity matters more than extra reach. This article compares 11 kg with a published reach of 900 mm; include the gripper and part in the load. |
→ CONSIDER FAIRINO FR10 Consider it when reaching farther matters more than the higher payload of the alternative. This article compares 10 kg with a published reach of 1,400 mm; include the gripper and part in the load. |
💡 THE TAKEAWAY Check the real tool, movement path and safety assessment before choosing. A collaborative label does not make every task safe without guarding; compare complete installation quotes. |
ABB SWIFTI CRB 1300-11/0.9 vs FAIRINO FR10 is a buying comparison built around the actual robot configurations, not a collection of family maxima. The low FR10 starting price should be compared with SWIFTI as a complete safeguarded process, not as a free-motion speed contest. The useful result is a cell that meets its load, quality, access and throughput requirements with a maintainable integration plan.
The starting-price figures used here are USD 45,000 for ABB SWIFTI CRB 1300-11/0.9 and USD 10,199 for FAIRINO FR10, taken from the individual ATC reviews. They are indicative review prices rather than binding current quotations. This guide separates rated payload, published workspace, positioning repeatability and complete-system requirements so that a cheaper or larger arm is not mistaken for a valid finished-cell alternative.
Quick verdict
ABB SWIFTI CRB 1300-11/0.9: A compact high-throughput cell with intermittent operator access and an engineered speed-and-separation-monitoring arrangement. The reviewed 6.2 m/s maximum TCP speed is not an unrestricted close-proximity operating speed. SafeMove and scanner coverage belong in the system concept. IP67 is an option on the reviewed IP40 base configuration.
FAIRINO FR10: Medium-load handling with a 10 kg rated load, 1,400 mm reach and a low indicative starting price. Use ±0.05 mm per ISO 9283, as specified on FAIRINO's FR10 page. The review's other ±0.02 mm headline should not silently replace this scoped value.
ABB SWIFTI CRB 1300-11/0.9 vs FAIRINO FR10: technical specifications
Specification | ABB SWIFTI CRB 1300-11/0.9 | FAIRINO FR10 |
|---|---|---|
Rated payload | 11 kg | 10 kg |
Published reach / geometry | 900 mm | 1,400 mm |
Position repeatability | ±0.02 mm | ±0.05 mm |
Controlled axes | 6 | 6 |
Arm / system mass in review | 75 kg | 40 kg |
Arm protection | IP40, IP67 optional | IP66 |
Controller / HMI | ABB OmniCore C30 | 10.1-inch teach pendant or web app on a mobile device |
Indicative starting price | USD 45,000 | USD 10,199 |
The figures refer to the variants discussed in the linked reviews. SWIFTI's reviewed high-speed capability belongs to a separation-monitored operating concept, not unrestricted close-contact operation.
Payload: start with the complete attached tool
ABB SWIFTI CRB 1300-11/0.9 offers 1 kg more nominal load capacity than FAIRINO FR10. A 10.5 kg complete tool-and-part combination already exceeds the smaller model's 10 kg headline limit. That does not automatically approve it on the larger robot: the load diagram, moments, inertia and worst wrist orientation still need to be checked. Use the rated configuration, not a family maximum.
For this pair, the reviewed masses are 75 kg for ABB SWIFTI CRB 1300-11/0.9 and 40 kg for FAIRINO FR10. Installation mass is separate from tool payload. Include the mounting frame, anchoring, lifting method and service access in the concept. A lighter arm may simplify handling, while a heavier installation may demand a different support structure; neither is a reason to omit dynamic-load and stability checks.
Workspace and posture: check every required pose
ABB SWIFTI CRB 1300-11/0.9 is listed with 900 mm, compared with 1,400 mm for FAIRINO FR10. These figures are useful for an initial layout but do not by themselves describe the usable workspace of the actual tool. An endpoint may be reachable while its required orientation, approach corridor or escape path is not. Include the machine door, fixture, cables and maximum part envelope in the study.
A matched joint count does not make the joint limits, singularity behavior, approach geometry or cable routing identical. Use a representative tool model in simulation or a physical trial. Include the deepest process pose, the farthest pickup, a reject position and a maintenance or recovery pose. If the cheaper concept needs an added slide or relocated fixture, count that work before comparing arm prices.
ABB SWIFTI CRB 1300-11/0.9: engineering assessment
The reviewed ABB SWIFTI CRB 1300-11/0.9 combines 11 kg rated load with 900 mm and ±0.02 mm positioning repeatability. Count replenishment, inspection and adjustment visits when estimating useful throughput. A fast robot that repeatedly slows or stops for people may lose its apparent advantage in a workstation designed for continuous shared access.
The reviewed 6.2 m/s maximum TCP speed is not an unrestricted close-proximity operating speed. SafeMove and scanner coverage belong in the system concept. IP67 is an option on the reviewed IP40 base configuration. Require a documented separation-monitoring layout and test access during the real production cycle. Scanner blind spots, stopping behavior and repeated operator entry can change the useful throughput.
FAIRINO FR10: where the alternative adds value
The reviewed FAIRINO FR10 offers 10 kg rated load, 1,400 mm and ±0.05 mm positioning repeatability. The price gap can be substantial, but the installed package and supplier responsibilities still decide value. Demonstrate diagnostics, backups and support arrangements with the actual offered controller and software revision.
Use ±0.05 mm per ISO 9283, as specified on FAIRINO's FR10 page. The review's other ±0.02 mm headline should not silently replace this scoped value.
Positioning, force interaction and process quality
The tighter stated position-repeatability value is ±0.02 mm, compared with ±0.05 mm for the other robot. That is a useful shortlist input, not a finished-part tolerance guarantee. Repeatability concerns returning to a pose under specified conditions; absolute accuracy, tool calibration, fixture movement and process variation remain separate engineering concerns.
FR10's source review contains a ±0.02 mm headline and a separately labeled ISO 9283 figure. The comparison uses ±0.05 mm per ISO 9283, as specified on FAIRINO's FR10 product page. That distinction matters when positioning performance is used to justify a price premium.
Programming, interfaces and ownership
The ABB source identifies ABB OmniCore C30. RAPID and RobotStudio are part of the ABB workflow described in the reviews. A familiar software environment can reduce maintenance friction, but only if the actual team can back up, diagnose and restore the application. Ask for the exact version and the rights to the finished program.
The alternative's reviewed control or HMI arrangement is 10.1-inch teach pendant or web app on a mobile device. The review describes graphical teaching and software integration options. Confirm enabled SDK, ROS and machine-interface capabilities on the supplied package.
Write an I/O and network schedule for the gripper, PLC, machine, inspection device and safety system. Verify voltages, connector pinouts, signal direction and timeout behavior. A protocol listed in a review is not proof that every license or board is supplied. Include a lost communication link, failed acknowledgement and an interrupted production sequence in the acceptance demonstration.
Safety, environment and real cycle time
SWIFTI requires a validated separation-monitoring concept. ABB describes SafeMove and safety scanning supervising access so motion can be managed when people approach. Include detection coverage, stopping behavior, replenishment and restart in the design. The published maximum TCP speed must not be presented as a speed for unrestricted contact with an operator.
The ABB review lists IP40, IP67 optional for the arm. The alternative is reviewed at IP66. Ingress ratings do not authorize every cleaning chemical, steam treatment or pressure-washing procedure. Check the controller, cable exits, connectors and tool independently, and distinguish standard protection from a paid option.
Compare useful output using the same part, tool, normal safety settings and peripheral delays. Maximum or typical TCP speeds are not a matched cycle-time benchmark. Gripping, machine dwell, process time and operator visits may dominate. Record good parts, rejected parts, changeover and restart time alongside motion time before turning a supplier demonstration into a payback estimate.
Price and total installed cost
The indicative starting prices are USD 45,000 and USD 10,199, a difference of USD 34,801. The lower-priced arm is FAIRINO FR10. Those figures come from the linked ATC reviews and may change. They do not establish equivalent controllers, pendants, safety equipment, software, stock or turnkey scope.
Request comparable bills of materials covering the robot, tool, fixture, machine interface, vision, safety devices, controller options, commissioning and training. Include freight, tax and installation where relevant. Name the supplier responsible for diagnosing faults across component boundaries and obtain configuration-specific warranty and delivery commitments. A cheap arm that needs an unsuitable layout changed is not automatically the cheaper installed system.
How to choose for a representative application
Decision | Start by testing | Why it matters |
|---|---|---|
Load and tooling | 11 kg versus 10 kg | Include all adapters and attached equipment |
Workspace | 900 mm versus 1,400 mm | Match geometric references and tool orientation |
Configuration | 6 versus 6 controlled axes | Do not merge different operating concepts |
Process quality | ±0.02 mm versus ±0.05 mm | Measure the finished result, not only robot position |
Value | USD 45,000 versus USD 10,199 | Align the installed package and maintenance plan |
The low FR10 starting price should be compared with SWIFTI as a complete safeguarded process, not as a free-motion speed contest. For the ABB candidate, the application to demonstrate is: a compact high-throughput cell with intermittent operator access and an engineered speed-and-separation-monitoring arrangement. For the alternative, evaluate: medium-load handling with a 10 kg rated load, 1,400 mm reach and a low indicative starting price. If a load, pose or safety requirement fails, redesign the concept before judging its apparent purchase-price saving.
Acceptance testing before purchase
Give both suppliers the same workpiece range, complete tool CAD, load data, required poses, target cycle, environmental exposure and intended operator interaction. Agree pass criteria before the trial. Test a missed pickup, a rejected part, a stopped machine and restart after power loss. Ask the intended operator to change a recipe and recover the sequence safely; a supplier-only demonstration is not a maintenance handover.
Retain the program, safety configuration, I/O schedule, tool settings and backup procedure. Establish support escalation, replacement-part responsibilities and the revision of the equipment being supplied. Where contact or dual-arm coordination is involved, keep the demonstrated process settings in the acceptance record so that later changes do not silently invalidate the qualified result.
Complete product reviews
Frequently asked questions
Which should I choose: ABB SWIFTI CRB 1300-11/0.9 or FAIRINO FR10?
The low FR10 starting price should be compared with SWIFTI as a complete safeguarded process, not as a free-motion speed contest. A compact high-throughput cell with intermittent operator access and an engineered speed-and-separation-monitoring arrangement. Medium-load handling with a 10 kg rated load, 1,400 mm reach and a low indicative starting price. Choose the concept that passes the actual tool-load, workspace, process-quality and safety tests with an acceptable installed quotation and maintenance plan.
What are the indicative starting prices in US dollars?
The ATC reviews list ABB SWIFTI CRB 1300-11/0.9 from USD 45,000 and FAIRINO FR10 from USD 10,199. The difference is USD 34,801. Prices are indicative and may change; confirm the supplied controller, pendant, software, safety equipment, tooling, delivery and integration scope.
Does the payload rating include the gripper?
Yes. Allocate the permitted load to the complete end effector, adapters and carried part, then check moments and inertia. The ratings used here are 11 kg and 10 kg. A part within the headline rating can still become an excessive load when its tooling is added.
Which has the longer usable workspace?
ABB SWIFTI CRB 1300-11/0.9 lists 900 mm, while FAIRINO FR10 lists 1,400 mm. Verify matching geometric references, tool orientations, approach paths and obstacles. A larger nominal number does not guarantee every required pose or a faster completed cycle.
Does repeatability guarantee the finished-part tolerance?
No. The comparison uses ±0.02 mm for ABB SWIFTI CRB 1300-11/0.9 and ±0.05 mm for FAIRINO FR10. These positioning figures do not independently establish absolute accuracy or completed-process tolerance. Fixtures, tooling, calibration, part variation and contact behavior must be included in the acceptance test.
Do collaborative robots always work without guarding?
No. The complete application needs risk assessment and validation. Tools, sharp or hot objects, trapping points, neighboring equipment and access patterns may require guarding, sensing, interlocks or speed limits beyond the arm's own functions.
Are all controller and software options included?
Not automatically. The source identifies 10.1-inch teach pendant or web app on a mobile device for FAIRINO FR10, but only a current quotation defines what is supplied and enabled. Confirm programming tools, protocol licenses, hardware interfaces, backups and ownership of the final application program.
What should the supplier demonstrate before purchase?
Require the real tool, representative parts and normal operating settings. Include critical poses, process quality, a realistic cycle, lost grip or communication, operator interruption and safe restart. Record acceptance criteria and retain the configuration and program used in the successful trial.
Specifications and indicative review prices describe the exact configurations discussed. Confirm the offered revision, package, safety requirements, warranty and delivery with the supplier. This is an editorial buying comparison and does not claim a hands-on performance benchmark.
